↓ Skip to Main Content

Murat's blog

Main Navigation

  • Home
  • About me
  • Voice Lab
Home › View all posts by adyg9

Author: adyg9

Adding A records to Expressway hosts.conf file

By adyg9 Posted on September 17, 2020 Posted in Collaboration Edge 3 Comments

So it finally happened to me – an MRA project with multiple domains. Previously I didn’t have to manually add entries to the hosts file on Expressway and needed to do some research. Here’s what came out of it: ‘A’ …

Adding A records to Expressway hosts.conf file Read more »

Ring No Answer Time (RONA/RNA) Configuration In UCCE 11.6

By adyg9 Posted on September 13, 2019 Posted in Cisco, Unified Communications No Comments

So I’ve had a problem with RONA where agents not picking up the call would be placed in ‘Not Ready – Call Not Answered’ state and, if there are no other available agents, placed back to ‘Ready’ again. The call …

Ring No Answer Time (RONA/RNA) Configuration In UCCE 11.6 Read more »

Prime License Manager license management reset

By adyg9 Posted on July 12, 2018 Posted in Cisco, Unified Communications

From PLM -> access to the CLI and issue the following command: license management reset {identity | registration} Take into account the following: This command resets the identity, store data, and essentially removes all the installed licenses. It also restarts …

Prime License Manager license management reset Read more »

Importing Netmiko library in Python

By adyg9 Posted on August 7, 2017 Posted in Python No Comments

To import Netmiko library run python -m pip install netmiko command in cmd After that we can successfully import Netmiko

Preparing VMware Workstation for CUCM installation

By adyg9 Posted on February 3, 2017 Posted in Uncategorized No Comments

In this post we will prepareVMware Workstation for the installation of CUCM 11.5. You can download the trial version of Workstation here. You should remember, that this installation is for lab use only and is not intended for production.

Connecting GNS3 to loopback interface

By adyg9 Posted on February 2, 2017 Posted in Cisco, GNS3 No Comments

To connect GNS3 to an existing loopback interface, add a router and a cloud devices.

Russian locale for Cisco 7821 IP Phone

By adyg9 Posted on January 26, 2017 Posted in Cisco, Unified Communications 3 Comments

While configuring Russian locale on CME, I came across a problem where 7821 phones would not switch to Russian locale. Turns out these phones look for localization file with different alias than the one created by CME router when locale …

Russian locale for Cisco 7821 IP Phone Read more »

Virtual Chassis configuration on Juniper EX4600

By adyg9 Posted on October 15, 2016 Posted in Juniper 1 Comment

So yesterday I’ve been configuring a two-member Virtual Chassis on Juniper EX4600. I’ve been following the guide but configuration wouldn’t save when issuing commit or commit synchronize command with the following error Member’s information missing from provisioning database Turns out, …

Virtual Chassis configuration on Juniper EX4600 Read more »

Upgrading IOS XE on ASR 1002

By adyg9 Posted on August 11, 2016 Posted in Cisco 3 Comments

So I needed to upgrade the IOS XE on customer’s ASR 1002 and after copying the image from USB to Flash, I issued a standard command boot system flash asr1000rp1-advipservicesk9.03.16.03.S.155-3.S3-ext.bin After reloading the router I get this error: boot: unsupported …

Upgrading IOS XE on ASR 1002 Read more »

Adding Loopback interface in Windows 10

By adyg9 Posted on July 26, 2016 Posted in Windows No Comments

To add a loopback interface in Windows 10, press Win+R and enter ‘hdwwiz’

Posts navigation

1 2 Next

Recent Posts

  • Adding A records to Expressway hosts.conf file
  • Ring No Answer Time (RONA/RNA) Configuration In UCCE 11.6
  • Prime License Manager license management reset
  • Importing Netmiko library in Python
  • Preparing VMware Workstation for CUCM installation

Recent Comments

  • Dark Rascal on Adding A records to Expressway hosts.conf file
  • adyg9 on Adding A records to Expressway hosts.conf file
  • Carlo on Adding A records to Expressway hosts.conf file
  • TNK on Virtual Chassis configuration on Juniper EX4600
  • Foad on Upgrading IOS XE on ASR 1002

Archives

  • September 2020
  • September 2019
  • July 2018
  • August 2017
  • February 2017
  • January 2017
  • October 2016
  • August 2016
  • July 2016

Categories

  • Cisco
  • Collaboration Edge
  • GNS3
  • Juniper
  • Python
  • Uncategorized
  • Unified Communications
  • Windows

Meta

  • Log in
  • Entries feed
  • Comments feed
  • WordPress.org
© 2023 Murat's blog | Powered by Responsive Theme